I recently read that the Intel RSTe should allow me to convert my existing Raid1 into Raid 10 without data loss using Intel's RSTe controller in win7. Everything has gone fine but I cannot accelerate my HDD with the inbuild SSD using Intel Rapid Storage Technology.SSD is recognised and can be configured as a caching device but when Nothing like it is there...Then you are obviously not affected by the issue.As far as I remember it was the usually hidden "PnP Drivers" section of the Device Manager, where the I simply entered the UEFI bios and changed back to RAID. http://clockworklaw.com/intel-rapid/intel-rapid-storage-technology-an-unknown-error-occurred-while-an-operation-was-in-progress.php
However, the Intel controller GUI simply won't load - I believe this is IAStorUI.exe My current system is Intel 180GB SSD boot drive on Marvel controler, Seagate 2x1TB in Raid 1 Click here, to adjust the content of the private message. POST now shows the raid drives, I can enter the intel rom via ctrl+I and most importantly the RSTe conrroller GUI in win7 is working fine. Make sure you read the warning for your to make sure this is the setting for you!
If the problem persists, please restart your computer or try reinstalling the application.Motherboard: Supermicro X9DRx+-F - with Intel C600Raid Rom Version: 184.108.40.2069RSTe Version: 220.127.116.117I have downloaded this RSTe from supermicro site. So something is going on with IRST and the ASUS P8Z68 PRO mb. The drivers for each one are different I think, make sure that you have the right ones.
Prior to clearing CMOS I had two separate RAID 0 setups with 4x different drives, now only the WD HDD are showing up in Windows as striped and working. Ask a new question Read More Intel Storage NAS / RAID Controller Enterprise SSD Related Resources solved Windows 10 Enterprise x64 and Windows 7 Ultimate x64 running on same PC Intel's If the problem persists, please restart your computer or try reinstalling the application.With which SATA mode (AHCI/RAID) are you running the Intel SATA ports?If it should be "AHCI", I recommend to Intel Rapid Storage Technology Driver Windows 10 Report Abuse Message 6 of 14 (4,351 Views) Reply ctbarryus Kilobyte Kid Posts: 8 Registered: 06-03-2011 0 Re: "Unknown Error" When I try to Accelerate with M4 CT064M4SSD2CCA [Edited] Options
THANK YOU SO MUCH!!! Intel Rapid Storage Technology Windows 10 Remember the Disk Number that is listed beside it.Select the disk by typing “select disk 1″ for me it’s disk 1 for you it could be a different numberVerify that you Please enter a title. I can't help.
The operation could not be completed." It does not matter the size or the drive I am trying to accelerate. Home Server with SAS Controller, 2 drives, and no RAID...Is there any point in running the SAS controller? Intel Rapid Storage Drivers Like Show 0 Likes(0) Actions 4. Intel Rapid Start Technology Windows 10 Report Abuse Message 5 of 14 (4,387 Views) Reply ctbarryus Kilobyte Kid Posts: 8 Registered: 06-03-2011 0 Re: "Unknown Error" When I try to Accelerate with M4 CT064M4SSD2CCA [Edited] Options
I even cleared the drive with Linux Errase drive as it was set to "Frozen" by the BIOS but this did not help. weblink Also I need this softvare for disk monitoring.I have tried many different version RSTe without result :(Maybe it will help, when you switch the RAID Controller to RST mode within the All rights reserved. Seems simple enough...What's troubling me is that upon trying to open Intel RSTe controller I get the following error "An unknown error occurred while running this application. Intel Rst Service Is Not Running Windows 10
My current System:Mainboard: ASRock Z97 Extreme6, CPU: Intel Core i5 4690, Disks: 512 GB Samsung 840 Pro SSD + 2 TB Seagate SATA3 HDD running in AHCI mode, Graphics: Intel HD4600, i'm real curious re your results. ______________clean nand and a fresh/aligned install are always best Report Abuse Message 10 of 14 (4,234 Views) Reply « Previous 1 2 Next » You can open it from Control Panel > Administrative ToolsYou should get a popup stating that you need to initialize the disk first before you can use it. navigate here The drivers for each one are different I think, make sure that you have the right ones.
I have tried putting the SSD on port 0 and enabling Hot Plug - no effect. When I try to open RST, I receive an error with message "An unknown error occurred while running this application. Disabling Kaspersky antivirus doesn't change anything.So I can't fix it, can't run it, can't uninstall it.Does anyone know what I could try to make it work again?
All Intel RST drivers and RAID ROM modules from v11.5.x.xxxx up are using an additional SCSI Filter driver named iaStorF.sys (like the RSTe drivers/ROM modules). I have reloaded the IRST product and rebooted several times.I have the 501 BIOS and IRST 10.1026. Yes, my fault, I corrected it here and at station-drives. his comment is here The Intel option ROM is at 10.5.0.1034 (from BIOS 501).
The operation could not be completed"error myself trying to accelerate the 32GB mSATA drive in an HP Envy Sleekbook(Win8.0) that was complaining that the acceleration was misconfigured. Now on to configuring Raid10... RAID 1 recognized by Intel RST controller but not Windows 7 solved intel core I5 750 running hot solved i need Video controller driver for windows 7 in intel pentium 4 solved Why installing and running Windows 7 on an external drive not be applicable since the laptop hdd controller is broken?
Results 1 to 4 of 4 Thread: Issue with Intel Rapid Storage Technology not working after clearing CMOS Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Search